Max. thrust: 750 N
Max. speed: 40 mm/s

Max. thrust: 750 N
Max. speed: 40 mm/s

Max. thrust: 400 N
Max. speed: 37 mm/s

Max. thrust: 8000 N
Max. speed: 13 mm/s

Max. thrust: 6000 N
Max. speed: 15 mm/s

Max. thrust: 3500 N
Max. speed: 46 mm/s

Max. thrust: 3500 N
Max. speed: 46 mm/s

Max. thrust: 6000 N
Max. speed: 30 mm/s

Max. thrust: 6000 N
Max. speed: 65 mm/s

Max. thrust: 6000 N
Max. speed: 33 mm/s

Max. thrust: 6000 N
Max. speed: 27 mm/s

Max. thrust: 2500 N
Max. speed: 43 mm/s

Max. thrust: 6000 N
Max. speed: 33 mm/s

Max. thrust: 7500 N
Max. speed: 15 mm/s

Max. thrust: 10,000 N
Max. speed: 18 mm/s

Max. thrust: 6,000 N
Max. speed: 19 mm/s

Max. thrust: 10,000 N
Max. speed: 160 mm/s

Max. thrust: 12,000 N
Max. speed: 7 mm/s

Max. thrust: 1000 N
Max. speed: 43 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 1600 N
Max. speed: 16 mm/s

Max. torque: 220/250 Nm
Average speed: 2.6º / sec.

Max. torque: 280 Nm
Average speed: 3.4º / sec.

Max. torque: 280 Nm
Average speed: 3.4º / sec.

Max. torque: 280 Nm
Max. speed: 0.58 Rpm

Max. torque: 350 Nm

Max. torque: 350 Nm

Max. torque: 350 Nm
Average speed: 5.0º / sec.

iMotor provides the movement and operates the switchgear. Linear as well as rotary movement is available.

The iSwitch Battery provides standby power for remote operations in the event of a local power failure.

iCom provides intelligent remote and local control and communication.

PAKNET is the communication modem for remote control. Various modem standards are possible.

iSwitch SAI is an iMotor Stand Alone Interface. When using iMotors with an existing control system a standardised interface is available.

Max. thrust: 1600 N
Max. speed: 43 mm/s

Max. thrust: 1000 N
Max. speed: 50 mm/s

Max. thrust: 800 N
Max. speed: 43 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 800 N
Max. speed: 34 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 800 N
Max. speed: 38 mm/s

Max. thrust: 2000 N
Max. speed: 18 mm/s

Max. thrust: 1500 N
Max. speed: 11 mm/s

Max. thrust: 6300 N
Max. speed: 21mm/s

Max. thrust: 2400 N
Max. speed: 18 mm/s

Max. thrust: 5000 N
Max. speed: 22 mm/s

CB6S is part of the LINAK OPENBUS product range. Compatible actuators: LA27C, LA31, LA34, BL1 and BL4 with mini-fit plug and standard end-stop switch / signal switch

Voltage in: 24 V AC (use TR7)
Duty cycle: 10%

Voltage in: 24 V DC (use charger)
Duty cycle: 10%

Voltage in: 230-240/120/100 V
Duty cycle: 5%
Max. Amp.: 8

Voltage in: 230/120/100 V AC
Duty cycle: 10%

Voltage in: 230/120/100 V AC
Duty cycle: 10%

Voltage in: 230/120/100 V AC
Duty cycle: 10%

Voltage in: 230/120/100 V AC
Duty cycle: 10%

CB16 is part of the LINAK OPENBUSTM product range. Compatible actuators: LA27C, LA31, LA34, BL1 and BL4 with mini-fit plug and standard end-stop switch / signal switch

Voltage in: 230/120/100 V AC
Duty cycle: 10%

Voltage in: 230/120/100 V AC (without battery)
Duty cycle: 10%

Voltage in: 230/120/100 V AC (without battery)
Duty cycle: 10%

Voltage in: 220-240/120/100 V AC
Duty cycle: 5%

Voltage in: 220-240/120/100 V AC
Duty cycle: 10%

Voltage in: 220-240/120/100 V AC
Duty cycle: 10%

Voltage in: 220-240/120/100 V AC
Duty cycle: 10%

The HB10 combines ergonomic design and functionality. HB10 is designed to operate with TWINDRIVE, LA27 and CB7.

The HB10RF gives the opportunity of integrating memory and infrared control with the TWINDRIVETM RF systems for leisurebeds.

The HB20 gives the opportunity of integrating memory and infrared control with the TWINDRIVE actuators.

The HB20RF gives the opportunity of integrating memory, infrared, control for massage and a child lock function with the TWINDRIVE actuators.

The HB40 handsets are designed for use with LINAK control boxes controlling single actuators or up to four actuators.

Handset up to 4 actuators. With memory. Applications: Hospital, patient care and industrial.

Handset up to 4 actuators. To be used together with the LINAK HOMELINE® system (LA29, LA31, CB7, CB9) with or without memory.

The HB70 has an IP 66 protection rating as standard and a range of options such as control of up to five actuators.

The HL70 has an integrated lock function and is thereby an alternative to our present ACP.

The HB80 is an ergonomic and easy to operate handset. This handset is the perfect choice with a CB20 Openbus system.

The HL80 is with integrated locking of each row. Supports up to 5 rows / 10 buttons.

The ACL (Attendant Control Lock) is fitted to beds for use where the patient positioning must be carefully controlled by the staff.

The ACM is a low-cost alternative to the ACP. It disconnects the function between handset and control box.

The ACP (Attendant Control Panel) is fitted to advanced hospital and care beds. It allows the nursing staff to retain direct control over critical functions.

The ACC (Attendant Control Compact) is a compact box with up to 11 buttons that can be used as Handset keys or Lock-outs. The ACC is compatible with control boxes that use an OPENBUS™ interface e.g. CB20.

The revolutionary OPENBUS™ system makes it possible to use keypads as Attendant Controls or Handsets integrated in the bed side rails. The keypads are named ACK (Attendant Control Keypads).

The ACO (Attendant Control OPENBUS) is a cost optimised and compact unit with up to 15 buttons that can be used as Handset keys or Lock-outs.

- Memory
- Up to 3 independent actuators

- Compact unit
- Up and down movement

- Basic compact unit
- Up and down movement

- Only up and down function
- Customised edition

- Simple up and down or with memory
- Different ways of mounting

- LED display for height indication
- 3 memory positions

- Memory function
- Displays height of desk

- Infrared communication
- Wireless control system

The FS Foot Switch is developed and designed for individual or parallel control of up to four actuators.

The FS2 Foot Switch is designed to be mounted on a frame. It is available in a single version and a double version.

- Display Memory
- Up to 3 different users

The BAJ battery pack has been specially developed for use with the JUMBO system. The battery pack is easy to exchange through an integrated snap system.

The CHJ2 charger has been specially designed for use as a wall-charger for the JUMBO system.

The COBO20 is specially developed for use together with the JUMBO battery pack and CU20.

For charging the batteries of CB08-XA and all JUMBO™ boxes directly connected to the control box or via the handset HB40A. With interchangeable plug types, optimising logistics.

For charging of the batteries in the control box CB8-XA, directly connected to the control box or via the handset HB40A.

The mains cut-off disconnects the mains voltage so that there is no mains voltage in the CB and mains cable when not in operation.

The DIN Junction Box is designed for the use with 2 x TWINDRIVE TD1 220, 250 or TD1 280 simultaneously with 1 or 2 controls.

The DIN Junction Box is designed for use where there is a need for more than 1 or 2 controls to be connected to a control box.

The MJB Modular Junction Box is designed for use together with the CB20 and other OPENBUS™ control boxes. The MJB makes it possible to connect handsets, attendant controls and accessories with the CB20.

Safety Limit Switch SLS. The SLS cuts off the current from the motor in either out- or inwards direction. Can also be used as signal switch. The SLS is available in protection class up to IP66 washable. For all LINAK® actuators.

IRO is a part of the accessory portfolio - available for the CB OPENBUSTM familiy. The Receiver is fitted to the bed so that the bed moveement can be controlled with signals received from a remote control.

Limit Switches LS/LSD. For industry actuators.

Electronic Limit Switches. For industry actuators.

LINAK has a range of extension cables and T-cables for handsets, desk panels and foot switches. LINAK also offers a range of extension cables for actuators.

Mounting brackets for the JUMBO system.

The BA18 has been developed for use with the control boxes: CB18, CB14, CB12 and CB9. BA18 has a capacity of 1.2 Ah at 24 V DC.

The TR6 is a seperate external power supply box, which can be wall mounted or placed on the floor. - Input 230V - output 24V AC.

The TR7 is a separate external power supply box, which can be wall mounted or placed on the floor moulding next to the mains.

The potentiometer is used where the absolute position of the actuator is needed.

The optical encoder is used for positioning and servo control of an actuator.

Massage Motor. Massage is now an option with the TD1 280 TWINDRIVE™ solution

The MEDLINE® & CARELINE® Division provides products for use in hospital and health care applications, thereby giving comfort for both patient and caregiver.

LINAK MEDLINE and CARELINE systems provide ideal solutions for use in hospital, nursing home as well as other health care equipment. However, the MEDLINE and CARELINE systems may also be applied in all kinds of clinics and fitness equipment, long-term care equipment in private homes as well as in other equipment used by disabled persons.

Both the MEDLINE and CARELINE systems are medically approved and their wide product ranges are designed for long life and hard use. At the same time, the solid constructions provide additional degrees of comfort and security to the patient. Additionally, all electrical components in the MEDLINE and CARELINE systems conform to the most stringent regulations for safety. Thus, the components are thoroughly tested to ensure they work safely in wet or damp conditions.

The MEDLINE system may be applied in various hospital equipment including hospital beds, patient hoists, incubators and stretchers. Besides, LINAK supplies a number of components to the dental chair industry.

Safety, easy to operate and comfort for patient and caregiver are some of the parameters that the wide range of MEDLINE systems fulfils. The electrically adjustable applications mean that the caregiver no longer has to make heavy lifts. In addition, the patient can make him or herself more comfortable and independent.

Furthermore, the MEDLINE system is medically approved and fully meets the requirements for IP 66 washable approved products for washing tunnels. Hence, all products in this system can resist the conditions and temperatures found within the washing tunnels.

The CARELINE system is typically built into health care equipment such as care beds, wheelchairs and bath lifts. Due to the electrically adjustable health care equipment the patient can find the position that he or she finds most comfortable and this often leads to self-sufficiency.
The CARELINE system is developed so that it is easy to operate and can therefore benefit both the patient and caregiver. Moreover, the CARELINE system has been developed with special attention to the demands of the care sector regarding safety and performance. For example, the system offers electronic overload protection (EOP), an IP 66 protection and a locking mechanism for plugs.

Furthermore, the CARELINE system is a complete system comprising up to four actuators, a fully integrated control box and controls. In other words, the CARELINE system allows a combination of several actuators and movements to be controlled via a single set of user-friendly controls and a control box.

 

The TECHLINE™ Division is focused on providing products for use in industrial equipment like machinery & workspace, building & construction, mobile equipment. Many years of experience and intensive product development has positioned LINAK as the leading developer and supplier of electromechanical quality actuators to the industrial and agricultural sector.

In order to focus on exactly the application you need, we have divided the industrial sector into three segments:

- Machinery & workspace
- Building & construction
- Mobile equipment
- Machinery & workspace

Today there is more and more focus on the working environment and thanks to LINAK´s products, it is possible to create ergonomic workplaces as the products help to reduce injuries caused by heavy lifting, repetitive strain and poor working positions. For example, the TECHLINE system can be mounted in working platforms, large mixer drums, conveyor belts, salt grid spreaders and feeding machines.

By equipping the various machines with products from the TECHLINE system, it is possible to ease the heavy loads, adjust the hatches, tilt the large mixer drums and so on. Moreover, the TECHLINE system has a colossal number of very different applications.

The TECHLINE system may also be installed in valves, dampers, smoke detections, ventilation shafts or other ventilation systems, thereby easing the work for many people. Moreover, LINAK provides a system that can easily reach inaccessible places, open or close sunblinds and roof windows, regulate ventilators, and close gates automatically. However, the possibilities are endless; it is only your imagination that sets the limits.

The TECHLINE system can be used in various industrial machines including lawn mowers, combine harvesters, salt grid spreaders, floor cleaning machines and platforms in cars.

In mobile applications the products often work under extreme conditions and they are therefore designed to function in harsh conditions such as water and steam, dust, dirt and variable weather. What is more, the products need no maintenance even though they are exposed to harsh conditions.

Studies show that a good working environment is of great importance. At LINAK we produce quality actuator systems and lifting columns that improves the working environment.

Due to DESKLINE® system people can sit or stand comfortably at their office or workplace as the DESKLINE system makes it possible for manufacturers of desks and other pieces of office equipment to install sophisticated motorized systems that provide optimum ergonomics and adjustable desk applications.

The key is to improve ergonomics at work by enabling the workplace to be adjusted to each individual, instead of making him or her adjust to the workplace.

The DESKLINE system may be built into office equipment including desks, workbenches and so on. Hence, the DESKLINE system is especially ideal at workplaces where multifunctional desks are required or in cases where several different individuals use the same facility.

Moreover, the wide range of DESKLINE systems allows desks, tables, kitchen units, conference tables, monitoring tables and even industrial workbenches to be raised, lowered or tilted at the touch of a button enabling each individual to find his or her desired working position that they find most comfortable. Thus, the DESKLINE range comprises products with large stroke lengths and small installation dimensions to ensure that people of any height benefit from the office furniture or other equipment fitted with LINAK’s products.

The wide range of DESKLINE systems consists of different kinds of actuator systems, lifting columns, built-in actuators and sophisticated control boxes to match. Nonetheless, each system may consist of up to six actuators or lifting columns all of which are connected to one or two control boxes and controls. In addition, the DESKLINE system is easy to integrate into any desk application, giving a wide range of movement and design possibilities.
 

When it comes to making life more comfortable at home, LINAK has more than 20 years of experience. With the HOMELINE® system LINAK is able to provide ultimate solutions for many different applications in the home.

Nowadays people focus more and more on the ergonomic aspects of daily life and as a result of this, the demand of comfortable and ergonomic furniture has increased. Thus, LINAK makes a great effort providing what you need to meet the present and future demands of the consumers. Hence, LINAK has developed the HOMELINE system.


By means of LINAK HOMELINE system, it is possible to enjoy the pleasures of comfortable and adjustable pieces of furniture at home. Moreover, the high force capacity makes it possible to incorporate HOMELINE actuators in chairs, beds, recliners, couches, massage chairs or other pieces of furniture used in private homes for comfort purposes. However, the number of applications of the HOMELINE system in the home is endless.

The HOMELINE system is developed to suit all aspects of daily life in private homes. Nonetheless, furniture mounted with the HOMELINE system is especially ideal for elderly people or disabled persons as it makes it easier for them to get up from the chair or couch. However, all people who enjoy the pleasures of comfortable and adjustable pieces of furniture can use furniture fitted with the HOMELINE system.

The HOMELINE system consists of up to four actuators, a fully integrated control box and controls. Furthermore, the memory function built in the control boxes enables each user to find and store his or her favourite position. In addition, the HOMELINE system is easy to fit and operate. The components also have a high reliability giving you the opportunity to design as well as produce furniture of high quality.
 

The NETLINE™ Division provides switchgear automation solutions for use in electricity distribution networks.

LINAK believes in supporting the ongoing changes within the Utility Markets to meet the demands for more efficient and effective power. The LINAK NETLINE solutions provide a simpler, safer, more reliable and cost effective answer in Network operability and performance.

Our NETLINE Division takes a global perspective on the efficiency of electricity generation, transmission and distribution. It is of significant importance to all of our futures.

The are many challenges facing the world demand for electricity that include ageing manually operated systems, limited funds, a reduced workforce and knowledge base, and at the same time the supply demands on the networks are increasing with high penalties for failure.

Our NETLINE Division is in tune with markets global challenges and is focused on meeting the Power Utility Sector requirements.